EP-CM-710 Hydraulic Pump Gearbox
The EP-CM-710 is an ultra-extreme-duty industrial PTO speed increaser designed specifically to couple the largest tractor power take-off (PTO) shafts directly to massive Group 3 and Group 4 hydraulic gear pumps. Featuring a highly efficient 1:3.8 step-up ratio, precision-cut helical gears, and an immensely rigid cast iron housing, this robust hydraulic pump drive gearbox efficiently converts low-speed tractor PTO power into the extreme high-speed rotation required for the world’s most demanding independent hydraulic circuits.
EP-CM-710 Hydraulic Pump Gearbox
The EP-CM-710 Hydraulic Pump Gearbox is a premium, ultra-extreme-duty agricultural power transmission unit engineered and manufactured by Ever-Power in Singapore. Designed to function as an immense PTO multiplier, the EP-CM-710 utilizes a 1:3.8 step-up gear ratio to convert a standard 540 RPM tractor PTO input into a rapid 2052 RPM output. This extreme speed multiplication is absolutely essential for driving massive Group 3 or Group 4 hydraulic gear pumps at their peak volumetric efficiency. Constructed with an exceptionally durable G25 cast iron housing and precision-machined helical gears, this 35-kilogram PTO to hydraulic pump adapter is built to safely transmit up to 82 kilowatts or 110 horsepower. It provides a highly robust, completely independent hydraulic power source for heavy tractor-mounted implements that require massive hydraulic fluid flow, completely bypassing the flow limitations of the tractor's internal hydraulic pump. The EP-CM-710 serves as a direct, high-performance agricultural hydraulic pump gearbox replacement for leading OEM brands, offering seamless dimensional compatibility with standard 1-3/8" 6-spline PTO shafts and standard European 4-bolt hydraulic pump mounting flanges.
Constructed utilizing extreme-grade G25 Cast Iron, providing exceptional structural rigidity and heat dissipation to handle the relentless radial loads and massive thermal output generated by ultra-high-pressure hydraulic pumping systems.
Features advanced helical toothing technology, ensuring optimized load distribution and significantly quieter operation compared to standard straight-cut spur gears, which is absolutely critical during high-speed 2000+ RPM rotation under a colossal 110 HP load.
Engineered as a high-performance PTO speed increaser, utilizing a highly efficient 1:3.8 step-up ratio to convert a standard 540 RPM tractor input into the precise high-speed rotation required for modern high-flow hydraulic gear pumps.
Designed with an optimized thermal mass featuring a 1.5 liter internal gear oil capacity, guaranteeing continuous splash lubrication to the heavy-duty deep-groove ball bearings and gear faces during relentless, continuous-duty hydraulic cycles.
Built to safely manage maximum input torque loads reaching a staggering 1450 Newton meters, efficiently transferring 110 HP of mechanical power to generate the extreme hydraulic flow and pressure required for the heaviest forestry and agricultural attachments.
Product Overview and Value Proposition
In the highly versatile and punishing realm of modern commercial agriculture, massive-scale forestry, and mobile construction equipment, hydraulic power is the fundamental driving force behind automated, high-output implements. However, many standard and heavy-duty utility tractors simply lack the internal hydraulic flow capacity (GPM) or the number of remote valves required to operate complex, extreme-demand attachments like massive tractor-mounted log splitters, heavy-duty forestry mulchers, high-flow trenchers, or industrial excavator attachments. The EP-CM-710 Hydraulic Pump Gearbox is meticulously designed from the ground up by our dedicated engineering team at Ever-Power to proactively solve this exact mechanical pain point on an industrial scale. By coupling this extreme-duty PTO speed increaser directly to your tractor's PTO shaft, you can instantly create an incredibly powerful, entirely independent hydraulic circuit tailored perfectly to your specific implement's extreme flow and pressure requirements.
When operating a high-flow attachment, the hydraulic gear pump must spin rapidly—typically between 1500 and 2500 RPM—to generate sufficient fluid velocity and pressure. Because a standard tractor PTO only spins at 540 RPM, a direct 1:1 connection is physically impossible without a heavy-duty step-up transmission. The EP-CM-710 tractor PTO hydraulic pump adapter bridges this mechanical gap, multiplying the input speed by a factor of 3.8. Even a minor mechanical failure or internal gear binding in a lesser aftermarket speed increaser can cause the hydraulic pump to seize or shatter, leading to expensive fluid contamination and total implement failure. Our uncompromising employment of an immensely rigid G25 cast iron housing ensures that the internal gear alignment remains absolutely perfectly centered, actively preventing the catastrophic failure of the main bearings under the severe side-loads of hydraulic fluid pumping. The immense structural integrity of the EP-CM-710 guarantees that the precision-ground helical gears remain in perfect mesh, delivering the steady, uninterrupted power required for your massive auxiliary hydraulic systems.
From a strategic fleet procurement and equipment manufacturing perspective, buyers are consistently searching for a highly reliable heavy-duty PTO multiplier that successfully balances premium longevity with sensible, cost-effective capital investments. Ever-Power delivers exactly this optimal balance. The EP-CM-710 is not merely a replacement component; it is a comprehensive, industrial-grade power delivery solution that guarantees operational continuity during extreme duty cycles. By strictly adhering to international manufacturing standards such as ISO and DIN, and ensuring seamless dimensional compatibility with massive Group 3 and Group 4 gear pumps, we entirely eliminate the engineering risks and fabrication costs typically associated with custom hydraulic setups. The EP-CM-710 stands as a testament to uncompromising engineering excellence, ensuring that your heavy-duty hydraulic implements run faster, stronger, and significantly longer than ever before.
Comprehensive Technical Specifications
To actively facilitate precise engineering evaluation, seamless system integration, and informed B2B procurement decisions, the specific technical parameters of the EP-CM-710 hydraulic pump drive gearbox are detailed in the comprehensive table below. All specifications are derived directly from our stringent engineering tolerances and load testing protocols based on heavy industry standards.
| Соотношение | Max Input RPM | Max Output RPM | Max Input Power Kw (HP) | Max Input Torque (N.m) | Max Output Torque (N.m) | Материал | Toothing | Weight (KG) | Oil Cap. (LT) |
|---|---|---|---|---|---|---|---|---|---|
| 1:1.5 1:2 1:2.5 1:3 1:3.5 1:3.8 |
540 | 810 1080 1350 1620 1836 2052 |
20 | 380 430 460 490 460 437 |
260 210 180 160 130 115 |
Aluminum | Cylindrical Teeth | 9.7 |
Data explicitly referenced from Ever-Power internal engineering documentation for the EP-CM-710 series. Designed for standard female 1-3/8" 6-spline input and standard Group 3 / Group 4 pump mounting.
Material and Manufacturing Excellence
The fundamental mechanical strength, extreme high-speed durability, and exceptional thermal resistance of the EP-CM-710 PTO speed increaser originate directly from our uncompromising approach to material science and advanced metallurgical processing at Ever-Power. Agricultural and forestry environments relentlessly expose sensitive hydraulic drivelines to intense vibration, shock loads, and continuous high-temperature operation. To aggressively combat this rapid physical degradation, the extreme-duty exterior housing is precision cast from superior G25 Cast Iron. Unlike cheaper aluminum housings that can warp under severe heat or crack under heavy PTO vibration, G25 cast iron provides massive structural rigidity, high tensile strength, and superior thermal dissipation properties, ensuring the gearbox for agricultural hydraulic systems survives extreme, relentless pumping conditions.
Internally, the high-speed multiplication capacity heavily relies on premium gears cut using industry-leading manufacturing processes. We utilize a highly specialized helical gear configuration for the EP-CM-710. Unlike straight-cut spur gears that whine loudly and vibrate severely at speeds exceeding 2000 RPM, helical gear teeth engage gradually. This allows for a perfectly fluid and continuous transition of rotational force, drastically reducing noise and mechanical vibration even under a massive 110 HP load. Every internal gear undergoes a highly precise carburizing and quenching heat treatment process. This advanced metallurgical procedure ensures that the outermost surface layer of the gear tooth achieves an exceptionally high hardness rating to actively resist wear over multi-year lifespans, while the inner core of the steel gear remains tough and highly ductile to safely absorb sudden resistance spikes from hydraulic pressure relief valves engaging.
The input and output shafts are supported by oversized, extreme-capacity deep-groove ball bearings designed specifically to accept the high-speed radial loads generated by the gear mesh and massive fluid pumping. To seal the internal unit against the harsh external environment and absolutely prevent gear oil from cross-contaminating with hydraulic fluid, we strictly utilize industrial-grade, double-lip nitrile rubber oil seals. This ensures that the critical 1.5 liters of internal gear oil remains perfectly contained while actively repelling agricultural dust, water, and abrasive debris.
Primary Application Scenarios
The highly engineered versatility, precise 1:3.8 step-up ratio, and massive 110 HP power rating of the EP-CM-710 allows it to serve as the exceptionally dependable primary power source for the heaviest auxiliary agricultural and forestry hydraulic systems.
🔸 Extreme-Duty Forestry Winches and Mulchers
The primary application for the EP-CM-710 is serving as the main hydraulic drive unit for heavy-duty, tractor-mounted forestry equipment. By connecting the gearbox directly to the tractor's PTO, operators can run massive, high-flow Group 3 or Group 4 gear pumps, delivering the 50 to 70 GPM required to cycle massive splitting cylinders or power industrial forestry mulchers rapidly, entirely independent of the tractor's internal hydraulics.
🔸 Large Front-End Loaders and Industrial Excavators
Heavy utility tractors often lack the hydraulic flow to operate massive add-on backhoe attachments, trenchers, or high-capacity front-end loaders efficiently. The EP-CM-710 agricultural hydraulic pump gearbox allows operators to mount a dedicated high-capacity pump to the rear PTO, running a separate, high-pressure hydraulic reservoir system strictly dedicated to the implement's valve bank for fast, incredibly responsive digging and lifting power.
🔸 Flail Mowers and High-Demand Hydraulic Motors
Implements driven by continuous-duty hydraulic motors, such as wide-swath ditch-bank flail mowers, rotary street sweepers, and massive agricultural augers, require immense amounts of continuous fluid flow. The EP-CM-710 PTO multiplier effortlessly steps up the 540 RPM PTO to drive the necessary heavy gear pumps, ensuring the hydraulic motors receive the steady, high-volume flow required to maintain optimal continuous operational speeds without bogging down.
Compatibility and Direct Replacement Guide
Ever-Power strongly recognizes that a vast segment of the global agricultural equipment market involves intelligently upgrading and rapidly replacing failed components on existing machinery to avoid devastating operational downtime. The EP-CM-710 tractor PTO hydraulic pump adapter is meticulously engineered to serve as a seamless, direct drop-in alternative for many prominent European and North American brands, significantly reducing maintenance downtime in the field.
If your heavy implement requires a highly reliable replacement gearbox utilizing 1:3.8 step-up ratios from manufacturers such as Comer Industries (ML series), Bondioli & Pavesi, or standard Italian Group 3/Group 4 pump adapters, the EP-CM-710 provides a highly attractive and extremely cost-effective upgrade path. We have perfectly matched the standard female 1-3/8" 6-spline input quick-disconnect coupling, ensuring that it locks directly onto your tractor's PTO shaft flawlessly. The massive output mounting flange is precision-machined to standard European 4-bolt patterns with the correct splined or tapered shaft reception, completely eliminating the need for manufacturing adapter plates or modifying the hydraulic pump housing.
Engineering Selection Guide
Selecting the absolutely correct technical specification of the EP-CM-710 gearbox requires a careful, methodical evaluation of your specific hydraulic system parameters to ensure safe, highly efficient, and incredibly long-lasting operation.
- First, you must accurately determine the displacement and maximum speed of your hydraulic gear pump. The EP-CM-710 multiplies a standard 540 RPM input to a 2052 RPM output. You must thoroughly verify that your specific hydraulic pump is rated to operate safely at 2052 RPM without suffering from internal cavitation (which destroys hydraulic pumps instantly).
- Second, meticulously evaluate the horsepower draw of your hydraulic circuit. The formula for hydraulic horsepower is (GPM x PSI) / 1714. If your massive pump generates 60 GPM at 3000 PSI, it requires approximately 105 hydraulic horsepower. The EP-CM-710 is rated for a maximum of 110 mechanical horsepower (82 kW), meaning it is perfectly sized for this heavy application. Do not exceed the 110 HP limit, as this will eventually shear the internal helical gears.
- Third, verify the physical mounting connection. The EP-CM-710 is typically supported directly by the tractor's PTO shaft, with an anti-rotation chain securing it to the tractor frame. You must ensure that the combined weight of the heavy cast-iron gearbox (35kg) and your specific high-capacity hydraulic pump does not exceed the overhung load limits of your tractor's internal PTO bearing.
Step by Step Installation Procedures
To guarantee the absolute reliability, safety, and warranty validity of your new EP-CM-710 PTO to Hydraulic Pump Gearbox, rigorous adherence to the following professional installation protocols is strictly mandatory for all maintenance personnel.
Preparation and Pump Mounting
Begin by meticulously cleaning the mounting face of your hydraulic gear pump and the output flange of the gearbox. Carefully slide the pump's splined or tapered input shaft into the gearbox's female output receptacle. Do not force or hammer the pump into place. Install the massive mounting bolts and use a torque wrench to tighten them in a crisscross pattern according to the pump manufacturer's heavy-duty specifications.
Tractor PTO Connection
Ensure the tractor engine is completely turned OFF and the key is removed. Liberally apply high-quality lithium grease to the tractor's 1-3/8" 6-spline PTO shaft. Depress the quick-release locking pin on the gearbox input coupling and slide the entire heavy gearbox/pump assembly onto the PTO shaft until the locking pin snaps firmly into the retaining groove.
Anti-Rotation Chain Installation
Because the gearbox is mounted directly to the spinning PTO shaft, it will naturally attempt to spin with the shaft. You MUST securely fasten the included heavy-duty anti-rotation chain from the designated mounting hole on the gearbox housing to a solid, stationary point on the tractor's drawbar or chassis. Ensure there is a slight amount of slack to allow for minor PTO shaft runout, but not enough slack to allow the heavy hydraulic hoses to pull tight.
Hydraulic Hose Routing
Connect your oversized low-pressure suction line and high-pressure output line to the hydraulic pump. Ensure all massive hoses are routed safely away from the spinning PTO shaft, the tractor tires, and any hot exhaust components. Secure them with zip-ties or heavy-duty hose clamps.
Lubrication Commissioning Procedures
The EP-CM-710 is shipped completely dry without any fluid to comply with shipping regulations. Operating this massive gearbox for even one minute without gear oil will cause catastrophic friction failure. Remove the top breather plug and carefully fill the gearbox with exactly 1.5 liters of premium SAE 90 or 80W-90 gear oil. Confirm the correct fluid level using the designated side level plug.
Preventative Maintenance and Lubrication
The operational longevity and mechanical reliability of the EP-CM-710 high-speed PTO multiplier is directly proportional to the quality and strict frequency of the preventative maintenance it receives in the harsh agricultural and forestry environment.
Initial Break-In Oil Replacement
During the first 50 hours of active pumping operation, the newly machined high-speed helical gear teeth undergo a natural microscopic polishing process. This safely sheds microscopic steel particles directly into the gear oil. You must drain and entirely replace the initial 1.5 liters of gear oil after exactly 50 hours of use. Perform this crucial oil change immediately after operating the implement, while the oil is highly heated and thin to flush all impurities effectively.
Routine Scheduled Lubrication
Following the initial break-in period, the gear oil must be replaced every 500 operating hours, or at least once annually before the primary working season. Continuous exposure to extreme temperatures and high-speed rotation degrades the extreme pressure chemical additives in the oil, necessitating strict replacement intervals.
Breather Valve and Spline Maintenance
The top oil fill plug incorporates a highly specialized mechanical breather valve. High-speed internal friction generates massive heat, causing air inside the casing to rapidly expand. If this tiny valve becomes clogged with field dust, the internal air pressure will build continuously until it forcefully blows out the heavy-duty input or output oil seals. Clean the breather valve vigorously with compressed air every month. Furthermore, thoroughly re-grease the PTO input splines every time you mount the gearbox to the tractor to prevent severe spline wear.
Advanced Troubleshooting Guide
Housing Overheating Diagnosis
The heavy cast iron housing will naturally operate hot to the touch (up to 85 degrees Celsius) due to the high-speed 2000+ RPM internal rotation. However, if the unit is severely overheating, emitting smoke, or boiling oil out of the breather, immediately stop operations. Dangerously low gear oil causes extreme metal-on-metal friction. Alternatively, the hydraulic pump may be dead-heading (pumping against a blocked valve), which forces the gearbox to constantly push against the massive 1450 N.m maximum torque limit, creating destructive thermal load.
High-Pitched Whining or Severe Vibration
While a slight gear whine is normal, a sudden, excessively loud high-pitched whining noise, accompanied by severe vibration, indicates failing internal ball bearings or a misaligned hydraulic pump. This is often caused by mounting a massive Group 4 hydraulic pump that is far too heavy, which places extreme overhung load on the gearbox output bearings without a secondary support bracket. Immediate replacement of the bearings is required.
Loss of Hydraulic Flow (No Output)
If the tractor PTO is spinning but the hydraulic implement is completely motionless, first verify that the gearbox locking pin has not sheared and the input shaft is actually turning the internal gears. If the input is turning, the internal connection between the gearbox output and the hydraulic pump shaft may have sheared off completely due to an extreme, sudden hydraulic spike (e.g., a jammed forestry winch or excavator cylinder).
Oil Seal Leakage and Fluid Mixing
If you notice gear oil leaking from the input shaft, replace the input seal immediately. CRITICAL: If you notice the hydraulic reservoir level mysteriously rising, or if the gearbox starts overflowing with fluid out of the top breather, the high-pressure shaft seal inside the hydraulic pump has blown out. This is forcing highly pressurized hydraulic fluid directly into the gearbox casing, mixing the fluids. You must replace the pump seal and completely flush the gearbox oil.
Часто задаваемые вопросы
Why do I need a PTO speed increaser instead of just plugging the pump directly into the tractor PTO?
Standard hydraulic gear pumps require high rotational speeds (1500-2500 RPM) to generate their rated fluid flow (GPM) and pressure (PSI). A standard tractor PTO only spins at 540 RPM. If you attach a pump directly to a 540 RPM shaft, it will only produce a fraction of its rated flow, making your heavy attachments run incredibly slowly and weakly. The EP-CM-710 steps the speed up by 3.8 times to solve this critical engineering issue.
What makes a G25 cast iron housing better than an aluminum housing for a 110 HP hydraulic pump drive gearbox?
While aluminum is lighter, it expands and warps significantly more under the massive heat generated by 2000+ RPM gear rotation and high-pressure hydraulic pumping at 110 HP. G25 cast iron provides immense structural rigidity, ensuring that the internal gear shafts remain perfectly parallel under extreme torque loads, which maximizes the lifespan of the bearings and gear teeth.
Why does this PTO multiplier use helical gears instead of straight-cut spur gears?
Straight-cut gears engage their entire tooth face at once, which causes severe noise and destructive vibration at high speeds. Helical gears are cut at an angle, allowing the teeth to engage gradually and smoothly. This provides much quieter operation, greatly superior load distribution, and higher durability at the 2052 RPM output speed of this massive gearbox.
Does the EP-CM-710 gearbox come pre-filled with lubricating oil directly from the factory?
No. To strictly comply with complex international shipping and environmental regulations, all EP-CM-710 units are shipped completely dry. You must manually add exactly 1.5 liters of premium SAE 90 or 80W-90 gear oil prior to mounting it to the tractor.
Can I run standard hydraulic fluid inside the gearbox since it is attached to a hydraulic pump?
Absolutely not. The gearbox and the hydraulic pump are two completely separate, sealed mechanical systems. The gearbox requires heavy-duty Extreme Pressure (EP) gear oil (API GL-5) to lubricate the high-speed metal-on-metal gear friction. Hydraulic fluid is too thin and lacks the chemical additives required to protect the gears from instantly destroying themselves.
Will this gearbox fit my massive Group 3 or Group 4 hydraulic gear pump?
Yes. The EP-CM-710 output flange is specifically machined to standard European 4-bolt specifications commonly used for heavy-duty Group 3 and Group 4 hydraulic gear pumps. Ensure you meticulously specify the correct output shaft reception (splined or tapered) when ordering to match your specific pump perfectly.
How tight should the anti-rotation chain be?
The anti-rotation chain should be snug enough to prevent the heavy gearbox from spinning around the PTO shaft, but it must have a slight amount of slack (about 1 to 2 inches of play). If the chain is pulled completely taut, it will bind the PTO shaft as the tractor moves over uneven ground, rapidly destroying the tractor's internal PTO bearings.
How do I properly prepare the PTO hydraulic pump adapter for extreme winter conditions in forestry applications?
In freezing climates, standard 85W-140 gear oil will become far too thick to flow properly during cold morning startups, leading to immediate high-speed bearing starvation. Switch to a high-quality synthetic 75W-90 API GL-5 gear oil approved for extreme cold weather operation to ensure immediate splash lubrication when the PTO engages at sub-zero temperatures.
What is the maximum size implement pump I can run with this gearbox?
The EP-CM-710 is rated for a massive 110 mechanical horsepower. This allows you to comfortably run large gear pumps producing roughly 55-70 GPM at 2500 PSI. Always calculate the exact required hydraulic horsepower of your specific pump to ensure it does not exceed the 110 HP mechanical limit of the gearbox.
Why does the hydraulic pump whine loudly when connected to the speed increaser?
If the gear pump is whining loudly, it is highly likely suffering from "cavitation". This occurs when the pump is spinning fast (2052 RPM) but cannot suck enough hydraulic fluid through the inlet hose. Ensure your suction hose is massively oversized (usually 1.5" to 2.5" minimum for large Group 3/4 pumps), completely unkinked, and the hydraulic fluid is warm enough to flow freely.
Anti-Hallucination Notes
Please note that all specific dimensional parameters, weight specifications representing 35 kg, oil capacities requiring 1.5 L, and horsepower ratings reaching up to 110 HP provided in this highly technical document are subject to variations based on the exact ratio configuration and mounting style ultimately ordered. Agricultural hydraulic applications are inherently subject to highly variable dynamic shock loads; therefore, peak input torque ratings of 1450 N.m should never be treated as continuous safe operating limits without proper engineering oversight regarding pressure relief valves. Always consult the certified technical schematics and engineering standards like ISO, DIN, and SAE provided by Ever-Power prior to final procurement and installation. The compatibility references to OEM brands indicate dimensional and performance equivalence for replacement purposes; the Ever-Power EP-CM-710 is an independent, premium manufactured product.
Knowledge Graph Navigation
- Upper Concept: Power Transmission Systems for Heavy Agricultural Machinery
- Lower Concepts: PTO Speed Increasers, Helical Gears, Cast Iron Housings, PTO to Hydraulic Pump Adapters, Auxiliary Hydraulic Circuits, PTO Multiplier
- Related Products: High-Flow Hydraulic Gear Pumps, PTO Drive Shafts, Hydraulic Control Valves, Heavy-Duty Forestry Winches, Flail Mower Gearboxes
- Related Industry Applications: Agricultural Forestry, Tractor Implements, Custom Hydraulic Circuits, Mobile Construction Equipment
Contact Ever-Power
To request exact technical schematics, secure bulk pricing for OEM integration, or to verify drop-in compatibility for your specific Group 3 or Group 4 hydraulic gear pump, please contact our Singapore engineering and sales team today.
Зубчатые редукторы
Производственные мощности мирового класса, поставщики качественных материалов и современный процесс качества позволяют EPT предлагать высочайший уровень точности, долговечности и выносливости. Планетарные редукторы EPT разработаны и изготовлены для передовых высокоскоростных применений с низким люфтом. Производственные процессы EPT позволяют нам предлагать исключительные возможности ударных нагрузок и различные варианты монтажа.
Обработка поверхности
Отжиг, естественная канонизация, термообработка, полировка, никелирование, хромирование, цинкование, желтая пассивизация, золотая пассивизация, сатинирование, черная окрашенная поверхность и т.д.
Метод обработки
Обработка с ЧПУ, штамповка, токарная обработка, фрезерование, сверление, шлифование, протяжка, сварка и сборка
Контроль качества и сертификат
Техники самопроверки в производстве, окончательная проверка перед упаковкой профессиональным инспектором качества
ISO9001:2008, ISO14001:2001, ISO/TS 16949:2009
Упаковка и время выполнения
Размер: Рисунки
Деревянный ящик/контейнер и поддон, или в соответствии с индивидуальными спецификациями.
15-25 дней образцы. 30-45 дней официальный заказ
Порт: Шанхай/Нинбо порт
ЧАСТО ЗАДАВАЕМЫЕ ВОПРОСЫ
Q: Вы торговая компания или производитель?
A: Наша группа состоит из 3 заводов и 2 корпораций по продажам за рубежом.
Q: Вы предоставляете образцы? Это бесплатно или дополнительно?
A: Да, мы можем предложить образец бесплатно, но не оплачиваем стоимость перевозки.
Q: Сколько времени длится ваша доставка? Каковы ваши условия оплаты?
О: Как правило, это 40-45 дней. Время может варьироваться в зависимости от продукта и уровня персонализации. Для стандартных продуктов, оплата: 30% T/T заранее, баланс перед отправкой.
Q: Что такое точный MOQ или цена для вашего продукта?
A: Как компания OEM, мы можем предоставить и адаптировать наши продукты к широкому спектру потребностей.Таким образом, MOQ и цена могут сильно варьироваться в зависимости от размера, материала и дальнейших спецификаций; Например, дорогостоящие продукты или стандартные продукты, как правило, имеют более низкий MOQ. Пожалуйста, свяжитесь с нами со всеми соответствующими деталями, чтобы получить наиболее точное предложение.
RU 
EN 
ES 
FR 
DE 
PT 
JA 
AR 
IT 
ZH