0 Items

The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for use with split-tapered sprockets and pulleys of the same Split Taper Bushing china bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you will need. For make use of with 5/8” shaft sizes. Comes with set screws. More Features: Made of Steel For make use of with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, preferably lowering readily available requirements and enabling changes in shaft size if important. The barrel of the split tapered bushing is usually split in two spots and is keyed to the shaft. The barrel OD is also keyed to the drive component as well. The good thing about the split tapered bushing could it be will hold, even if the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.

Taper bushing are trusted together with sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed of high quality engineered elements with wonderful tolerance. The characteristic is easy to apply and needs no added alteration. These bushings can fit almost all sorts of assemblies and sizes. They are the best choice in style for mechanical connections.
To complete designations add bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total range of both metric and imperial readily available.
Standard range suits up to 125mm/5″ shafts & Hub diameter required will depend on the application.
Complete brief reach range offered, for compact light and portable assemblies & Clean, Compact Design.
Simple installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on a single page as the pulley you need.
For use with 1 3/16” shaft sizes.
Comes with 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for strength and strength. U1 bushings are being used in an extensively wide range of applications, which include; sprockets, shaves, pulleys, gears, and much more, we also offer most of these goods. What sets this bushing apart may be the high-quality steel development along with precise manufacturing and high quality control; this means that you always get yourself a premium quality steady product. What really units us in addition to the other men is our experienced expert workers and our company-wide aim of customer satisfaction.
1. Be certain the tapered cone areas of the bushing and the within of the driven product happen to be clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or different part type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to assure sliding in shape on shaft.
4. With important on shaft, slide the sprocket or other component type to the desired situation on the shaft. Make sure you keep the heads of the cap screws available.
5. Align the sprocket or component type, tighten the screws on the other hand and progressively until they happen to be pulled up tight. Usually do not make use of extensions on the wrench handles and don’t permit the sprocket or part to end up being drawn i connection with flange of bushing. At this time there must be a gap between the bushing flange and sprocket, make sure this gap does not close.
Double split barrel ensures concentricity
Grips the shaft with confident clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or tied to mounting screws
External key of all sizes for great drive and increased torque carrying capabilities
Double-split barrel for confident clamping
Solid flange to maintain concentric bores
Available in inch, metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Double Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys in both shaft and item to provide the strongest possible drive.
3/4″ per Foot Taper on Barrel – Self locking taper provides the highest degree of mechanical locking item to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on a single page as the pulley you will need. For use with 5/8” shaft sizes. Includes set screws. Additional Features: Manufactured from Steel For apply with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, preferably lowering on hand requirements and enabling alterations in shaft size if required. The barrel of the split tapered bushing is certainly split in two places and is usually keyed to the shaft. The barrel OD can be keyed to the drive component aswell. The advantage of the split tapered bushing is it will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.