WPWKT Series Universal Worm Gearbox

The WPWKT Series is an EVER-POWER universal worm gearbox manufactured in Hangzhou and supplied factory-direct from Singapore. Gear ratios 1:5 – 1:60, max output torque 3,025 N·m, efficiency 60-82%. Input: Solid shaft. Output: Hollow bore shaft. Mounting: Universal – multi-position. Centre distance 40-250 mm. 20CrMnTi worm hardened to HRC 58-62. ISO 9001:2015 and CE certified. MOQ 10 pcs. Sample in 15-25 days. 24 h quote response.

UGS : WPWKT Catégorie : Réducteur à vis sans fin universel Étiquettes : Réducteur à vis sans fin universel, réducteur de vers universel, moteur à vis sans fin, réducteur à vis sans fin, réducteur à vis sans fin

Description

ISO 9001:2015
CE

Input

Solid shaft

Vertical — upward

Output

Hollow bore shaft

H7 tolerance

Ratio

1:5 – 1:60

Universal single stage

Max Torque

3,025 N·m

Size 250

Mounting

Universal – multi-position

40–250 mm

1:5 – 1:60

Gear Ratio

60–82%

Efficacité

3,025 N·m

Max Output Torque

HRC 58–62

Gear Hardness

40–250 mm

Centre Distance

Product Overview

WPWKT Series Universal Worm Gearbox — Technical Overview

The WPWKT Series Universal Worm Gearbox provides a vertical upward input shaft and a hollow bore output shaft in the universal P-type housing. The motor mounts below the gearbox with its shaft pointing upward; the driven machine shaft engages the hollow bore directly without a coupling.

Vertical upward input shaft (T position), hollow bore output to H7 tolerance, integral P-type HT250 cast iron universal housing. 20CrMnTi worm shaft at HRC 58–62, ZCuSn10Pb1 bronze wheel, 60–82% efficiency. Oil fill adjusted for T orientation.

Factory-direct from Singapore. View the Réducteur à vis sans fin universel range or request a quotation.

WPWKT worm gear reducer internal structure and component diagram

WP Series Worm Gear Reducer — Internal Structure and Main Components

Shaft Direction

WPWKT Series — Input and Output Shaft Orientations

Multiple shaft direction positions are available. Specify the position code when ordering. Oil fill volume changes with non-standard orientations — EVER-POWER confirms the required adjustment.

WPWKT worm gear reducer shaft direction diagram — input and output shaft orientation positions

WPWKT Series — Shaft Direction Diagram · A: input below · S: input above · O: output upward · X: output downward · T: input upward · V: input downward

Code	Input Shaft Position	Output Shaft Position	Typical Use
UN	Horizontal — below centre (standard)	Horizontal	Horizontal conveyor drives, standard floor-mounted machines
S	Horizontal — above centre	Horizontal	Overhead mounting, inverted or top-fed drives
O	Horizontal	Vertical — upward	Lifting columns, vertical screw drives, hoist applications
X	Horizontal	Vertical — downward	Gravity-assisted feed, downward discharge drives
T	Vertical — upward	Horizontal	Vertical input from above, tower or mast drives
V	Vertical — downward	Horizontal	Floor-level motor with downward vertical input shaft

ℹ Vertical Upward Input + Hollow Bore Output — WPWKT Series

The WPWKT combines the T-position (vertical upward input) with hollow bore direct shaft output. The motor installs below the gearbox; the driven shaft engages the horizontal hollow bore from the side. Both the input coupling (motor to worm) and the output coupling (worm to driven shaft) are eliminated, minimising drive train component count.

Dimensional Drawing

WPWKT Series — Overall Dimensions and Mounting Geometry

Full dimensional data covering 40–250 mm centre distance range. 2D DXF and PDF drawings available within 24 hours at no charge.

WPWKT worm gear reducer dimensional drawing — overall dimensions mounting hole pattern and shaft sizes

WPWKT Series — Structural Dimensional Drawing · All dimensions in mm · Sizes 40–250 mm · DXF and PDF on request within 24 hours

Dimension Symbol Reference

A / AB	Overall length / length excluding shaft extension	B / BB	Overall height / base plate height
CC	Output shaft centreline height above base	HS / U	Input shaft diameter / usable shaft length
T x V	Input shaft key width x key depth	LS / S	Output shaft usable length / diameter
W x Y	Output shaft key width x key depth	E / F / G / M / N	Foot mounting hole positions and pitch

Spécifications

WPWKT Series — Full Parameter Table

Input speed: 1,500 r/min · Housing: HT250 cast iron · Seal: NAK / SKF · Lubricant: ISO VG220 · MOQ: 10 pcs · Port: Shanghai / Ningbo

WPWKT worm gear reducer specification table — input power and output torque for all sizes and ratios (brochure p.26)

WPWKT Series — Parameter Table (brochure p.26) · Columns: Size · Ratio · A/AB/B/BB/CC/H/HL/M/N/E/F/G/Z · Input shaft HS/U/T×V · Output shaft LS/S/W×Y · Weight (kg) · Oil (L)

Taille	Ratio	Max Input (kW)	Max Output Torque	Weight (kg)	Oil (L)
WPWKT Series · Integral cast iron (P-type) · Universal – multi-position · 20CrMnTi Worm · ZCuSn10Pb1 Bronze Wheel · Input: 1,500 r/min
40	1/5–1/60	0.48	26 N·m	5	0.15
50	1/5–1/60	0.80	43 N·m	9	0.47
60	1/5–1/60	1.25	70 N·m	12	0.57
70	1/10–1/60	1.60	113 N·m	18	0.96
80	1/10–1/60	2.20	163 N·m	24	1.26
100	1/10–1/60	3.60	305 N·m	41	3.01
120	1/10–1/60	5.20	440 N·m	68	4.51
135	1/10–1/60	9.75	740 N·m	91	7.01
147	1/20–1/60	8.50	883 N·m	111	8.81
155	1/20–1/60	12.80	883 N·m	129	9.61
175	1/20–1/60	17.30	1,272 N·m	172	11.21
200	1/20–1/60	22.60	1,856 N·m	241	13.51
250	1/20–1/60	27.40	3,025 N·m	396	22.51

* Peak output torque at the highest-torque ratio per size · Full ratio-by-ratio data available — request the complete data sheet

Material and Construction

Engineering Specifications — WPWKT Series

Worm Shaft

Primary drive element

Alloy grade20CrMnTi

Surface hardnessHRC 58–62

Traitement thermiqueCase carburising + quenching

Surface finishGround, Ra ≤ 0.8 μm

Shaft core40Cr steel

Roue à vis sans fin

Output driven element

Alloy gradeZCuSn10Pb1 tin-bronze

Tooth formZI involute profile

Bearing brandSKF / C&U / HRB

Shaft sealNAK / SKF lip seal

Leak test2.5 bar · 100% of units

Housing and Assembly

Structure and sealing

Housing gradeHT250 grey cast iron

Housing formIntegral cast iron (P-type)

LubrifiantISO VG220 gear oil

InputSolid shaft

OutputHollow bore shaft

Selection Correction Factors

Power Calculation and Correction Coefficient Tables

Apply correction factors a₁ and a₂ to the rated torque before selecting a gearbox size. Use Table 3 to verify motor input power.

Table 1
Ambient Temperature Correction Coefficient a₁

Ambient Temperature (°C)	10 – 25	26 – 30	31 – 40	41 – 50
a₁	1.0	1.1	1.0	1.6

Table 2
Duty Condition Correction Coefficient a₂

Operating Condition	Daily Running Hours (h)
Operating Condition	≤ 2 h	> 2 – 10 h	> 10 – 24 h
Smooth running	0.8	1.0	1.2
Moderate shock load	1.0	1.2	1.4
Heavy shock load	1.25	1.5	1.75

ℹ If the gearbox starts, reverses, or changes direction 12 or more times per hour during operation, multiply the table value by an additional factor of 1.2.

Table 3
Input Shaft Power Calculation and Efficiency Coefficient u

Input Power Formula

P = T × n₂ ÷ (9550 × u)

P — Input shaft power (kW)

T — Corrected torque value (N·m)

n₂ — Output shaft speed (r/min)

u — Transmission efficiency (from table below)

Ratio	1:10	1:15	1:20	1:25	1:30	1:40	1:50	1:60
Efficiency u	0.76–0.90	0.75–0.86	0.74–0.84	0.72–0.82	0.68–0.70	0.65–0.75	0.62–0.72	0.60–0.70

Lubrification

Recommended Lubricants by Speed and Temperature

Select oil grade based on worm shaft speed and mounting orientation. Change after the first 100 operating hours, then every 2,500 hours.

Oil Grade Selection by Worm Shaft Speed and Operating Position

Worm Shaft Speed (r/min)		Oil Type	Upper Worm / Vertical	Lower Output Shaft Vertical
Over	Up to
1,000	3,000	Synthetic oils	PG460	PG220
—	1,000	Synthetic oils	PG460	PG460
2,000	3,000	Mineral oils	ISO VG460	ISO VG200
750	2,000			ISO VG320
250	750			ISO VG460
—	250	Mineral oils	ISO VG660	ISO VG660

International Brand Equivalents by Ambient Temperature

Ambient Temp.	Oil Type	Esso	Texaco	Mobil	Shell	AGMA
15–60°C −9 to −16°C	Mineral oils	Spartan EP220	Regal Oil R&D 320	DTE LIL BB	Shell Omala Oil 220	5
	Compounded oils	Sparan EP320	631-Honor Cylinder Oil	Mobil 600W Cylinder Oil	Shell Omala Oil 320	7
	Extreme pressure	Spartan EP460	Meropa 460	Mobil Gears 634	Shell Omala Oil 460	7EP
50–125°C 10–52°C	Mineral oils	Spartan EP320	Regal Oil 320	DTE OIL AA	Shell Omala Oil 320	6
	Compounded oils	Spartan EP460	642-650T Cylinder Oil	Mobil 600W Super Cylinder Oil	Shell Omala Oil 460	8
	Extreme pressure	Spartan EP680	Meropa 680	Mobil Gears 636	Shell Omala Oil 660	8EP

ℹ Drain and flush the unit after the first 100 operating hours. Thereafter, change oil every 2,500 hours or 12 months, whichever comes first. Use synthetic oil for continuous 24-hour duty.

Fault Diagnosis

Troubleshooting Guide — Common Faults and Remedies

Identify the fault symptom, locate the probable cause, and apply the recommended corrective action before returning the unit to service.

Fault Symptom	Probable Cause	Recommended Action
Overheating	Motor, gearbox, or driven machine misaligned at coupling	Re-align all three shafts to be co-axial. Check coupling and re-torque fasteners.
	Overload running	Reduce load to within rated torque. Apply correction factors a₁ and a₂.
	Lip seal worn or excessively tight	Apply grease at the seal lips; replace seal if worn.
	Incorrect oil level or degraded lubricant	Top up or drain and refill to the correct level. Use the grade specified in Table 4.
Vibrations	Motor, gearbox, or driven machine poorly fixed or misaligned	Inspect and re-tighten all mounting fasteners. Re-align coupling.
	Worm wheel tooth surface worn or damaged	Replace the worm wheel assembly.
	Bearing worn	Replace bearing. Check shaft for scoring before refitting.
Abnormal Noise	Bearing worn or clearance too large	Replace bearing and adjust preload.
	Poor worm wheel tooth mesh	Check and adjust tooth contact; replace worm wheel pair if necessary.
	Insufficient lubricant	Top up oil to the correct level.
	Foreign matter in housing	Drain oil completely, flush housing, remove debris, refill with fresh oil.
Oil Leakage	Lip seal damaged	Replace lip seal.
	Shaft journal surface worn at seal contact	Replace input or output shaft. Fit new seal to match.
	Oil overfilled	Drain to the correct level per the oil gauge indicator.
	Drain plug loose or oil gauge cracked	Re-seal and tighten drain plug. Replace oil gauge if cracked.
Rapid Worm Wheel Wear	Overload running	Reduce load; check application duty factors against rated capacity.
	Wrong lubricant grade	Drain and refill with the correct grade from Table 4.
	Insufficient lubricant	Top up to the correct level at the oil gauge.
	Oil change interval exceeded; lubricant degraded	Drain, flush, and refill per the maintenance schedule.
	Operating temperature too high	Resolve overheating fault first (see above), then reduce ambient temperature or improve ventilation.

Applications

WPWKT Series — Industry Use Cases

EVER-POWER worm gearbox manufacturing facility Hangzhou — CNC gear hobbing and precision assembly

EVER-POWER Manufacturing

CNC gear hobbing, heat treatment, and 100% pressure-testing in Hangzhou. Every WPWKT unit is inspected and pre-filled before dispatch.

WPWKT worm gear reducer installed in industrial drive application

WPWKT Series in Service

The WPWKT worm gear reducer serves conveyor, mixer, packaging, and agricultural drives across 40–250 mm centre distance.

🏭
Sub-Floor Motor Hollow Bore Drive

WPWKT 80–250
Vertical up + hollow bore

Sub-floor or pit motor installations where the motor shaft points upward into the gearbox and the driven shaft engages the horizontal hollow bore without a coupling.

🚧
Low-Profile Hollow Bore Conveyor

WPWKT 60–200
Hollow bore + vertical in

Conveyor drives with below-floor motors where the conveyor shaft engages the hollow bore directly, eliminating the coupling at both gearbox ends.

⚙
In-Pit Drive with Direct Shaft Engagement

WPWKT 100–250
Up to 3,025 N·m

In-pit process drives where the motor occupies the pit, the gearbox is at process level with vertical upward motor input, and the driven shaft engages the hollow bore directly.

🌾
Agricultural Sub-Ground Hollow Bore Drive

WPWKT 40–120
Vertical in + hollow out

Agricultural installations where the power source is below ground and the driven shaft at ground level engages the hollow bore directly at the gearbox output.

Fabricant

EVER-POWER PTE. LTD. — Factory Direct from Singapore

Singapore-registered. Hangzhou manufacturing. No intermediaries — factory pricing and ISO-certified quality on every order.

EVER-POWER worm gearbox factory Hangzhou — production floor

EVER-POWER Production Base · Hangzhou, China · 3 Plants · CNC Gear Hobbing · Heat Treatment · 100% Pressure-Test

EVER-POWER PTE. LTD.

Singapore Registered · Hangzhou Manufacturing · 20+ Years Experience

ISO 9001:2015
CE Certified
Triple ISO

🏭 3 Plants Manufacturing Facilities CNC gear hobbing, case-hardening, assembly, and 100% pressure-test in Hangzhou.	🔬 HRC 58–62 Worm Shaft Hardness Case carburising and quenching on every shaft. Ra ≤ 0.8 μm ground finish. Hardness verified by Rockwell test.	📦 MOQ 10 pcs OEM from Small Batches Custom ratios, shaft sizes, keyways. Sample 15–25 days; production 30–45 days.
🌎 50+ Countries Global Export EU · US · UK · AU · NL · BR · CA · KR. DDP and DAP available.	📋 Triple ISO Certified Quality ISO 9001:2015 · ISO 14001 · ISO 45001. CE marking on request.	⚡ 24 h Quote Response Send size, ratio, quantity, application. Full quote + drawing within 24 hours.

Frequently Asked Questions — WPWKT Series Universal Worm Gearbox

How does the WPWKT differ from the WPWKV?+

WPWKT has vertical upward input (T); WPWKV has vertical downward input (V). Both have hollow bore output. They are mirror input configurations.

Does the WPWKT need a special oil fill?+

Yes. T-position changes the oil bath level. EVER-POWER specifies the fill volume at order.

Does the WPWKT self-lock?+

Yes, at ratios of 1:30 and above.

What is the MOQ and lead time?+

MOQ 10 pcs, 30–45 days. Samples 15–25 days.

Are drawings available?+

2D DXF/PDF within 24 hours.

Request a Quote — WPWKT Series Universal Worm Gearbox

Provide your required centre distance (40–250 mm), gear ratio (1:5 – 1:60), shaft direction, mounting type, and quantity. Full quotation with dimensional drawing returned within 24 hours.

MOQ 10 pcs

Sample 15–25 days

Quote in 24 hours

DDP / DAP available

Request a Quote →
Email Us Directly

📞 +65 8866 2737 · Singapore

Réducteurs à engrenages

Des capacités de fabrication d'engrenages de classe mondiale, des fournisseurs de matériaux de qualité et un processus de qualité de pointe permettent à EPT d'offrir le plus haut niveau de précision, de durabilité et d'endurance. Les réducteurs planétaires EPT sont conçus et fabriqués pour des applications avancées à grande vitesse et à faible jeu. Les processus de fabrication d'EPT nous permettent d'offrir des capacités exceptionnelles de résistance aux chocs et diverses options de montage.

Traitement de surface

Recuit, canonisation naturelle, traitement thermique, polissage, nickelage, chromage, zingage, passivation jaune, passivation or, satin, peinture noire, etc.

Méthode de traitement

Usinage CNC, poinçonnage, tournage, fraisage, perçage, meulage, brochage, soudage et assemblage

Contrôle de qualité et certificat

Autocontrôle des techniciens en cours de production, contrôle final avant l'emballage par un inspecteur de qualité professionnel.
ISO9001:2008 , ISO14001:2001,ISO/TS 16949:2009

Emballage et délai de livraison

Taille : Dessins
Caisse/conteneur en bois et palette, ou selon les spécifications du client.
15-25 jours pour les échantillons. 30-45 jours pour les commandes commerciales
Port : Shanghai/Ningbo port

FAQ

Q : Êtes-vous une société commerciale ou un fabricant ?
R : Notre groupe se compose de trois usines et de deux sociétés de vente à l'étranger.

Q : Fournissez-vous des échantillons ? Est-ce gratuit ou en supplément ?
R : Oui, nous pouvons offrir l'échantillon gratuitement, mais nous ne prenons pas en charge les frais de transport.

Q : Quel est votre délai de livraison ? Quelles sont vos conditions de paiement ?
R : En général, le délai est de 40 à 45 jours. Le délai peut varier en fonction du produit et du niveau de personnalisation. Pour les produits standard, le paiement est le suivant : 30% T/T à l'avance, le solde avant l'expédition.

Q : Quel est le prix exact de votre produit ?
R : En tant qu'entreprise OEM, nous pouvons fournir et adapter nos produits à un large éventail de besoins. Par conséquent, le MOQ et le prix peuvent varier considérablement en fonction de la taille, du matériau et d'autres spécifications ; par exemple, les produits coûteux ou les produits standard auront généralement un MOQ moins élevé. Veuillez nous contacter avec tous les détails pertinents pour obtenir le devis le plus précis possible.